A Different Kind of Knife...

...and even a spoon. It's a little late to be making this post considering I made these fiddleback redgum butter knifes and a jam spoon for Mothers' Day, but I forgot to take a photo at the time and keep forgetting to take my camera when I see Mum. Until now.



Forgive the B&W photo. I've since learned that using a red and white checkered tablecloth as a background leads to very red, overexposed images.

What Makes a Knife a Knife?

As you (the reader of this blog) may be aware, I have been following The Suburban Bushwacker for some time now and recently made him a knife to review. Well this isn't a link to the review (that's to come later) but I'd like to share this informative article he's written on buying the right knife.


If you have a general love of the outdoors, and/or bushcraft I'd also recommend having a look through his other posts. In fact, have a read even if you're not into bushcraft and spent your days in a darkened room surfing the net.. it might help.

Photo Credit: Todd Hill - Primitive Point

Knives by Dave Myhill

I met Dave Myhill about 7 years ago when I was at the home of my best friend (Dave's daughter, L) having a bit of a catch up, and he dropped over for a visit.
At the time, Dave was a little apprehensive about the boys his daughter spent time with, and had the misconception that this young lad sipping tea with his only female heir must be her boyfriend, or at least a potential candidate - so he offered to take me hunting, and said he'd even give me a 3 day head start.

Dave also took the time to explain that he could lodge a knife, bullet, or arrow in me from 30 yards with very little difficulty on his part.

We had a few chance encounters shortly after that (helping L move house, the occasional shared meal, birthdays, etc.) and we gradually began to warm to each other. On several occasions I even made the trip to Dave's place on the Mornington Peninsula with L to help out with some yard work.

A few short years later Dave and I really started developing a friendship. He'd tell me at great length about knives and damascus steel and I was fortunate enough to spend some time with him in the shed getting a crash course in forge-welding.

Sadly, Dave passed away at the beginning of last year after a lengthy battle with cancer. This was pretty hard to take considering Dave had become very much like a second father to me.
I'm not sure if this is the right choice of words but maybe the one good thing to come from this was that it prompted me to start making knives on my own. At some point in the future I hope to start my first forged knife and give the finished product to L as a tribute to her father's dedication to the craft of knifemaking.

While recently attending the knife show I ran into a friend of a friend and she introduced me to her partner A, who happens to be a knife collector.
We got to talking and it turns out A rarely missed an opportunity to wander past Dave's stand at shows past and usually walked away with one of his knives.

He offered to let me come over and look at his collection, and was kind enough to donate some of Dave's unfinished blanks, agreeing that as payment I would put a handle on one of them for his partner.


I've decided that I'll finish the large trade blade and keep that for myself, but the large dagger will be redesigned into a tanto style blade for an old friend and the smaller utility knife will be finished and one day be given to my godson - who happens to be one of Dave's grandchildren.

The Bushwacker - No Longer Just a Concept

It feels like a very long time ago that I emailed SBW asking if he wanted to review a knife. We had a great deal of emails go back and forth, nutting out the details of the design and materials to use, and most of the time having a good chat too.
This was a huge learning curve for me. Firstly, I had to make something to somebody's specifications - everything I've made so far has been my design and I've been able to allow the blades to evolve as I either make mistakes or change my mind. So this time around, every time I did something wrong my shed would be filled with colourful language as I tossed aside something I'd broken, bent, burned, gouged, melted, chipped, or just generally been unsatisfied with, and then started making it again.

This was the first knife I've made out of a file, and I quickly found that annealing it with a blowtorch just isn't enough. This required annealing several times before I could get it to a workable hardness (or softness).

G-10 is an incredibly unforgiving material. Try shaping it with anything other than a brand new belt and it turns black and starts smoking before your very eyes. I used an entire block of material before I managed to figure out the right pressure when grinding.

The welded buttcap was the last straw - even with the welder on it's lowest setting, I managed to melt part of the tang into a small V indent (which is still there) and simply couldn't fix without risking more damage. This was after the first welding attempt saw the buttcap fall off after it was welded on, shaped, and sanded back to a smooth finish. I actually consider myself to be a fairly passable welder, but arc welding something so small is pretty tricky stuff.

Still, it's all experience and I can finally say that the knife is finished. I just hope SBW finds it to his liking.

BlackRabbit Logo

I know this blog is called Obsidian Rabbit but truth be told, when I started thinking of trading names for my knifemaking the first thing that came to mind was BlackRabbit. Sadly that name is already being used for another blog, which serves another purpose - but that doesn't mean I can't still use the name for my knifemaking.
So now I have a logo.

Utility Knife Step-by-step: Part 2

I got so caught up in the moment of shaping the handle that I completely overlooked taking any photos of the process.
In a nutshell though, I shaped the handle using the bench grinder. I actually started with the stone wheel which might sound strange for use on wood but it does wonders with removing large quantities at once. I then shaped further using the belt grinder and drum sander.
After shaping the handle I finished sanding the blade with wet and dry, going from 80 grit through to 800.
Then I sanded the handle to 240 grit and finished off with an 800 grit sanding pad. This was followed by several applications of danish oil with a light sand in between coats.
And for the final touch I ran the flade over a clean sisal wheel.

The results are as follows:





The filework shows up really well with the black epoxy.


There are some bits I could have done better but overall I'm rather happy with how things turned out

Utility Knife Step-by-step: Part 1

Ok, it's been a long time coming but I've finally managed to get some work done in the shed and will now attempt to explain how I make a knife.
I've actually been a little sceptical about doing this post because it really is a 'warts and all' insight into how I put a knife together. It shows the mistakes I make as I'm learning this craft and the efforts I put into correcting those mistakes.
If for example, I manage to bust one of the scales as I'm grinding the handle, I'm more inclined to try to repair it than start again.
It's a learning curve for me and I'll know not to do whatever I did wrong next time around.
The way I see it is this: These are knives I make for myself and for my close friends and family. If you give someone something you've spent countless hours producing, it's unlikely they'll nitpick about an imperfection.

I'll warn you now, this is a long post and some of the pics were rushed so please forgive my photography this time around.

Everything I've made so far has been done using the stock removal method. This involves taking a piece of steel, cutting a knife 'blank' out of the material (I use an angle grinder with a cutting wheel), and then shaping the steel using whatever means one has available before finally adding a handle and finishing the knife.
There are other steps involved in this process and I'll try to detail them as I go.

I've already cut out the blank, as per my last post and need to continue grinding the steel to refine the profile and overall shape of the knife.
What I didn't mention in my last post is that with some of the steel I use I need to anneal it before working on it - in some cases before even cutting out the blanks. The pieces I'm working on now are all from a piece of HRPO which is tough as anything so I gave it a quick run over with the MAPP torch right after I scribed the blank patterns into it - I did this so it wouldn't rip through my cutting wheels, and even then I was still using on average one wheel per blank.
I then gave the blank another pass with the torch after it had been cut out, bringing it up to cherry red and then letting it cool slowly before beginning the grinding process.

I don't have pictures of this in progress but I used a multi-tool linishing attachment on my bench grinder to grind the profile into the blade. I've basically moved the blank from the ricasso to the tip on each side of the blade horizontal to the belt until I'm happy with the amount of material that has been removed.
After doing this, I've draw filed the blade so I can have more control over the shaping.
I haven't draw filed before making this blade but I'm pleased that I did because previously I feel I've overdone it with grinding and haven't ended up with the type of finish I was after. I found it's also a lot easier for me to put a ricasso on the blade using a file rather than the belt.


After shaping the blade I've drilled holes for the pins. I'm trying a few different things this time around. It's a full tang knife so I really want to make sure the handles hold strong so I'm putting in 4 small pins and two larger ones.

Because I'm a dolt and never bother to properly measure anything I have 4 extra holes that I won't be using - but they'll be covered by the handle and will give a little room for extra glue.


In the spirit of self discovery and learning I decided I'd have a go at making some mosaic pins. I'm not going to go in to detail on how this was done in this post but I learned how to do it http://www.northcoastknives.com/northcoast_knives_tutorials_hints_tips4.htm and here.

The gist of it is: insert a few bits of wire into a larger diameter tube with glue and allow to set before sticking in a knife handle.


I've also done a little filework on the spine of the tang, following a tutorial I found here.


For the next part I've put one of the handle scales in the vice and drilled holes for the larger pins and the lanyard hole. I've then used the pins to hold the knife in place on top of the scales so I can drill the 4 smaller holes.



After the holes are drilled swap out the scale for the undrilled scale, replace the knife and the pins (though now they're the other way around) and drill through the existing holes so they're mirrored in the other scale (I hope that made sense).


With all the holes drilled I'm now ready to assemble the handle and glue everything up. For additional places for the glue to run I've drilled a few indentations between the pin holes on the inside of the scales.


Before I assemble the handle I heat treat the blade - this deserves a more detailed description so I'm saving this for another post.

Before I glue anything I make sure all the pin holes line up so I don't work out something has gone wrong as I'm gluing everything together.
I apply epoxy to the insides of the handles, to the tang, and press it into each pin hole before inserting the pins and clamping everything in place.
I added a little black ink to the epoxy - explanation for this will come later.


I'll post part 2 in a few days.

New Blanks

I admit it - I'm slack. I haven't posted in a bit, and that's because I haven't been making any knives recently. A lot of other things have been happening (ala Christmas) but I'm back in the swing and I'll be putting up more posts shortly.
I made a few new blanks last week and have picked out the one I'll be working on first. I usually work on a few things at once but for the moment I'll be focusing on making a utility knife. I'll do my utmost to show step-by-step the process I use for making knives with this one as the example.
Thanks for reading. And thanks for your patience.


The four blanks: Two utilities, and two hunters/skinners. I'm going to grind one of the utilities further so it can have a half-tang handle.


The full tang utility after a quick shape on the grinder. More "in progress" pics to follow in a later post.

Bush Knife

I thought while I was at it with making big knives, I'd try my hand at a bush knife. I guess you could call it a machete but that makes it sound rather aggressive so I'm sticking with bush knife.

A friend kindly handed me a few lengths of HRPO (Hot-Rolled Pickled & Oiled) steel. That stuff is STRONG! I thought I'd try cutting a piece off to work with before I annealed it, and it made a mess of the cutting disc I had on my grinder.

So the design isn't really my own - I borrowed a few ideas from here and there. But I figure that I'm not making and selling these so making one for personal use shouldn't stir anyone up too much.

I wanted to have a billie hook but keep the rest of the design as simple as possible so the handle is just a paracord wrap. I say 'just' lightly though - for functionality purposes I'd take paracord over the nicest of timbers.

I've got the macho knives out of my system for now so I'll be going back to something smaller for the next post.

Bowie Knife

I've never had a bowie knife. I know they have a function (aside from looking menacing), but most of the time I don't need anything that big - and if I do, I reach for the axe.
But I wanted to try making one - I also wanted to try making a half tang knife. And the thing I learned.. is that I'll need to try harder next time. I was rushed with this one, and I think knowing that I was making it for myself, I didn't give it the attention it deserved.
So on to the details. I started out with a piece of tool steel, annealed it with the ol' blowtorch, and cut out the blank with an angle grinder, then shaped it up on the bench grinder.
The design wasn't too difficult to come up with - but given that I keep breaking steel guards when I'm trying to make them I cut up a piece of micarta and used that for the guard - that was my first mistake.
The micarta slabs I have really aren't that thick, maybe 10mm. So I had to drill the holes for the tang but leave enough space around them for the rest of the guard. To make the handle not look rediculious, I made this a similar thickness - so when I had glued everything up and got to shaping it, I ended up cutting in too deep and as you can see from the pics, ended up with a resin pommel/butt/bolster/what have you.
I also managed to overshape the micarta top the point where there is a very deep groove where the guard meets the shoulder.
Like everything in this blog, it was a learning curve - and I'm happy to learn - but I do hope I do better next time.
Oh, and before I forget - the wood is curly birch. I gave it a little brown leather stain for the colour.

Knife for my Brother

I wanted to make a knife for my brother this time around. We both love fishing and camping so I thought a full tang camp knife would be ideal. It's the same shape as the one I made for Dad with a few variations in the design.
I gave this one a partial scandi grind and some filework along the spine. The handle is made from soapwood and ringed myall with a fibre spacer.
I was pretty happy with the way this knife turned out. It could have done with less gaps when I epoxied it and some of the pins didn't work out the way I had hoped but it's all good experience, and my brother didn't offer up any complaints. He was pretty pleased in fact.

Firesteels

I've been looking around at some of the firesteels (Swedish Firesteel, Blast Match, Metal Match, etc.) and even though I've already got a few of these I thought I'd have a go at making a couple of my own.
I bought some ferrocerium rods from an importer in Queensland and turned up a couple of handles on the bench grinder - wood for one and micarta for the other. I think they came out rather well considering it only took about 5 minutes to make each one, with the exception of the time it took for the Araldite to dry.

A few Sheaths

A few months back I'd been thinking for a while about making some sheaths - or more to the point, replacing the nylon sheath that came with my Winchester knife, with a homemade leather sheath.
I've done a little leatherwork in the past so the learning curve wasn't that great. That said, there's still a lot I need to learn and practice makes perfect.. eventually.
I also made a Scandinavian style sheath for a small damascus blade that I picked up at a show.

Mini Skinners

I was pretty happy with my first attempt at a skinner so I made a few mini versions. I thought one of these would be good to throw in with my camping kit, as a sort of emergency knife for 'light' bushcraft needs.
I decided to make these in two different styles.
The paracord wrapped one is a drop point and the other (hoochie cord wrapped) has a more traditional trailing-point spine.
I also chose to give both knives a smooth, seamless bevelled edge, and left out a ricasso to give a longer blade length that could start a cut from either the point or rear of the blade.

A new Knife

I thought I'd try my hand at some cord wrapping, so I decided to make a knife to practice on.
I didn't have a skinner so it seemed the perfect choice. I didn't really like the finish and was getting a bit bored with the hand sanding so I treated it with gun blue - so it's now got a nice gun-metal grey finish.

The First Knife

Well, I've officially made my first knife. It's father's day today and I've just handed it over to Dad for his gift.
I knew when I started making it that I wanted to give it to Dad - just seemed like the right thing to do. It's not the best knife I'm ever going to produce - with practice I'm sure I'll get much better - but I can only make one ''first'' knife so I wanted Dad to have this one.

It's made from (what I believe to be) O2 steel and I used stock removal for the process. The handle is redgum and the guard is stainless.

Had a hell of a time making the thing - I can say I've learned a lot of lessons about grinding and drilling in the process - like, don't use a grinding wheel on the guard once it's on the knife. The thing fell off several times because the heat kept melting the epoxy. I know now to either shape the entire thing first or just use the slack band of the belt grinder.

Let The Blogging Begin

I thought I'd put together a general blog for my projects - in part so I can show some of the things I make and get some feedback, and also so I can look back on things at a later time and see how I've (hopefully) learned from any mistakes I've made. Enjoy.